Sometimes your computer may give an error when using the Canon i80 troubleshooting guide. There can be many reasons that can cause this error.
Fix your computer now with ASR Pro
After connecting the manual to the printer, pressing the power button does nothing.
The problem is most likely in the power cord. Examine the cable to find exposed cables if there are other problems. Try moving all cables and pressing the charge button at the same time to see if the cable is frayed and possibly only working at a certain angle. If you can make it strong this way, try using duct tape with duct tape to secure the wire in the position it will do its job. If you don’t like it, try the next step.
Unplug the power cord from the user’s outlet, turn it on and try using a different outlet. Try a different outlet with the same device and try a different device. If it is powered by more than just an outlet, it means that your cord is definitely broken.
Unfortunately, the Canon i80 is no longer sold by Canon, so you cannot order a replacement cable for it.
There may be different cases. There may be factors with the paper. If people are convinced that there is a problem with printingIf not related to paper, scroll down to the Tattoo Ink Solutions section.
1. Make sure the document is the correct thickness. The paper inside the Canon i80 must be at least 64 g / m² and no more than 105 g / m². The thickness of the paper should be indicated on the enclosed packaging.
2. Make sure the paper is not wrinkled or creased. If so, replace it with smooth glossy paper and try again.
3. Clean the pick roller in steps 1 to 2, but the problem persists. Turn off the printer and remove any paper from the paper tray.
4. Press and hold the Resume / Cancel button at the same time. Release the button after the Power light blinks three times. The paper feed roller can rotate and self-clean.
5. Load a stack of white newsprint into the printer and repeat step 4. The loaded paper will pass through the printer and ejected, usually completing the cleaning process by pointing to the paper feed roller.
1. The stump has jammed the tattoo paper. Do this either through the card exit slot where the printed document exits, or through a large part paper feeders. Be careful not to damage these printers.
2. Open the printer cover and remove any pieces of paper that are stuck in the printer’s print head.
3. Close the printer cover, reinsert the paper tray if necessary, and then press the Resume/Cancel button to continue copying.
When trying to print a document, the document cannot be printed. Paper printer, but buys.
1. Turn on the printer, press and hold the RESUME button until the printer light blinks once. You (Note: You can also clean the printhead by clicking the “Cleaning” button on the “Maintenance” tab of the “Inkjet Printer Properties” dialog box in Windows; you can click the drop-down menu of the “Cleaning dialog box.” If you select this option, you can choose all misty, black or just colored jets.)
2. If you press Continue on the printer, all nozzles are likely to be cleaned. When the print head starts cleaning, the POWER indicator will flash. This will go on for almost 30 seconds.und. Wait until the indicator stops flashing before resuming normal operation. Run the nozzle check pattern test again.
3. If all test results are not satisfactory, perform another print head deep cleaning.
If the dialog box shows a package with the message “Summer ink absorber full”, replace the ink absorber:
1. Make sure printer type is off, and I would say printer is off. Press Resume/Cancel, then Power. Keep holding the “Power” button, but leave “Resume/Cancel”.
2. Click Resume/Cancel three more times. Release the Power button. Also, click Resume/Cancel four times. The color of the printer changes from red to green. If this absolutely does not fix the problem, you may need to replace the tank.
3. Unplug the new printer from the power source. Remove the back cover of the printer you normally use with a screwdriver. On the right, there is a simple clip and screw at the bottom that hold the position in place. Remove the tr strips of adhesive tape securing part of the tank and surrounding wiring. This frame is usually yellow. Move the cables aside.
4. Remove the summer from the printer and attach a new one. Make sure the nozzle is lined up like a straw with an open hole. Be sure to secure the cables with insulating tape or office tape. Replace the entire back of the printer.Download this software today to get your computer back up and running.
Guide De Depannage Canon I80
Przewodnik Rozwiazywania Problemow Z Canon I80
Felsokningsguide For Canon I80
Guida Alla Risoluzione Dei Problemi Di Canon I80
Guia De Solucao De Problemas Canon I80
Guia De Solucion De Problemas De Canon I80
Rukovodstvo Po Ustraneniyu Nepoladok Canon I80
Canon I80 Anleitung Zur Fehlerbehebung
Canon I80 문제 해결 가이드
Canon I80 Gids Voor Probleemoplossing